Still looking for a round tank.

[Esteban]

A lot of old lawnmowers, garden tractors, go karts, stationary engines, etc., used that type of tank. On the " Bay ", do a search for vintage gas tanks.
Like this ??

http://cgi.ebay.com/ebaymotors/VINT...m14QQhashZitem170273230354QQitemZ170273230354

 

[HoughMade]

I think ebay is always a good place to look. I would suggest that something sturdy be used. There are beverage containers made of thin aluminum I would not use because they would be dangerous. You do not want something that will split easily....that's a recipe for burning flesh.

 

[jimraysr]

eBay for gas tank?

Good find. That is what I have been looking for.

The first thing I did was call lawn mower repair shops and they hadn't seen one in years. )

The problem with any small keg would be the expense of getting the aluminum fittings and then the welding. Didn't really look like a good option. If I were building a dune buggy, the 15 gallon beer keg would be a good option.

Hope the eBay item is still reasonable in 6 days when the bids ends?

Jim

A lot of old lawnmowers, garden tractors, go karts, stationary engines, etc., used that type of tank. On the " Bay ", do a search for vintage gas tanks.
Like this ??

http://cgi.ebay.com/ebaymotors/VINT...m14QQhashZitem170273230354QQitemZ170273230354

 

[sjackson]

You don't need welded fittings. What you want to look for is something called a "deck fill" for a boat. They're anywhere from $10-$40 depending on how fancy you get.

http://www.discountmarinesupplies.com/HARDWARE-Deck_Fills.html

I was planning on using one of these on a fabricated fiberglass tank. The screws probably won't sink into the thin metal on the mini keg though. I would recommend cutting off the filler tube so you can reach in there with your fingers and use a nut and bolt to secure it.

Also, as fun as it is to empty a mini-keg that has been filled with delicious beer, getting an unused one has it's advantages. namely that you don't have to clean any paint off of it, and it only has one hole in the side instead of two:

http://www.midwestsupplies.com/products/ProdByID.aspx?ProdID=4900

 

[Esteban]

A tank like that , in good shape, will probably bring $20. Look thru all the pages at this site to see MANY tanks like it. You may post on their forum as well.
http://www.asecc.com/gallery/page1.html

 

[jimraysr]

Mini-Keg And Deck Fill

I love the idea. The deck fill does answer the filler problem. The mini-keg looks to have a plastic plug (bung) in the top? (or end if laying down). What is the arrangement? The second hole you mention must be for a spigot installed at the bottom?

I stopped the suds 26 years ago, so have missed out on a lot of the developments in the industry. )

There is a West Marine up the steet so getting the deck fill should be a snap.

Since you have worked out the big problem, what would you suggest for the outlet / drain cock?

Harbor Freight has a blind nut tool that works great for installing a nut in a metal plate. It works like a pop rivet, only pulls the threaded end up under the inside of the metal and mushrooms the barrel. I think it puts in half a dozen sizes up to 1/4". I have only used it to install some 1/4" nuts for CCTV mounts. There are a number of places on motorized bikes where it would be good to have a captive nut.

Jim

You don't need welded fittings. What you want to look for is something called a "deck fill" for a boat. They're anywhere from $10-$40 depending on how fancy you get.

http://www.discountmarinesupplies.com/HARDWARE-Deck_Fills.html

I was planning on using one of these on a fabricated fiberglass tank. The screws probably won't sink into the thin metal on the mini keg though. I would recommend cutting off the filler tube so you can reach in there with your fingers and use a nut and bolt to secure it.

Also, as fun as it is to empty a mini-keg that has been filled with delicious beer, getting an unused one has it's advantages. namely that you don't have to clean any paint off of it, and it only has one hole in the side instead of two:

http://www.midwestsupplies.com/products/ProdByID.aspx?ProdID=4900

 

[jimraysr]

Antique Engines

The antique engine thing could be a whole new hobby. I saw mention of a Maytag engine. Dad used to talk of a Maytag washer they had on the farm (Bond County IL). Little flex pipe exhaust trailing a stream of blue smoke while washing the 10 kids clothes. )

Jim

A tank like that , in good shape, will probably bring $20. Look thru all the pages at this site to see MANY tanks like it. You may post on their forum as well.
http://www.asecc.com/gallery/page1.html

 

[xPosTech]

If push comes to shove and you have to fabricate one diesel exhaust pipes (F350, etc.) go up to 4". Muffler shops should have odds and ends.

Get a 12" piece, cap the ends, 1/4"NPT for an outlet and a vented gas cap, a little paint and you're in business. Leather mounting straps from an old belt would give a vintage look.

Ted

 

[Esteban]

Link to an old Maytag " Hit & Miss engine.
http://www.youtube.com/watch?v=ap4x8HvQX0k&feature=related

 

[loquin]

too bad you weren't looking earlier...