Here is my latest Fosscati FG4 Billinudgel Bullet. It has a few improvements from the original one shown elsewhere in that it has a paint job on the tank that is baked on in layers, the hub clamp is 318 grade s'steel, the muffler strap is 318 s'steel, the tank is mounted on a strip of high density adhesive foam tape so you don't need to tighten the tank legs to refusal and damage the tank, all bolts are Aussie steel with locnuts on the end, the springer bolt has a locnut & cotter pin on it so it can't come undone & thornproof tubes & slime in both tyres. This is the 8th Bullet I have built and they all have Honda motors - I doubt the HuaSheng could pull this heavy steel bike but the new G4 gearbox might enable it to. Nobody seems to want the HS motor even though they are 20% of the Honda price once I include for adapting the carb and governor. Personally I don't think the Honda is worth the difference which is about Aus$700.
The chain is still being stretched so the line of it isn't how I like it. I stretch all chains and ride each bike for 200 kms before hand them over to their new owners. I'm not happy with using the Grubee tensioners and need to make that my next focus for change. They are quite OK if used by an experienced person but very dangerous if incorrectly fitted by a novice. The gearboxes all whine to varying degrees - some are really bad.
Anyway this bike is going to a bloke in Darwin which is 3700 kms from where I live. Any volunteers to ride the bike there?
These bikes ride really well and have great balance but I personally prefer the alloy framed Schwinns because they are sportier and more responsive but the drawback with the alloy Schwinn is that the 7.5" headtubes can't accommodate a springer fork and that makes for a bumpier front end.
Oh yes I almost forgot - of the 12 Schwinn cruisers I have bought there have been 13 saddles (one was a tandem) - those dual sprung saddles that have springs just like Madonna's bra - every single one comes apart on day one or day two and I have had to disassemble and reassemble every one with threadloc and fabricated washers etc to get them to stay in one piece. this is a really serious defest in the design and assembly and even though I'm now very good at fixing the saddle it still takes a lot of time before I can be sure the saddle springs won't crunch through the supporting bracket when you are riding the bike. Lovely looking saddles but the old rice farmer story again.
The chain is still being stretched so the line of it isn't how I like it. I stretch all chains and ride each bike for 200 kms before hand them over to their new owners. I'm not happy with using the Grubee tensioners and need to make that my next focus for change. They are quite OK if used by an experienced person but very dangerous if incorrectly fitted by a novice. The gearboxes all whine to varying degrees - some are really bad.
Anyway this bike is going to a bloke in Darwin which is 3700 kms from where I live. Any volunteers to ride the bike there?
These bikes ride really well and have great balance but I personally prefer the alloy framed Schwinns because they are sportier and more responsive but the drawback with the alloy Schwinn is that the 7.5" headtubes can't accommodate a springer fork and that makes for a bumpier front end.
Oh yes I almost forgot - of the 12 Schwinn cruisers I have bought there have been 13 saddles (one was a tandem) - those dual sprung saddles that have springs just like Madonna's bra - every single one comes apart on day one or day two and I have had to disassemble and reassemble every one with threadloc and fabricated washers etc to get them to stay in one piece. this is a really serious defest in the design and assembly and even though I'm now very good at fixing the saddle it still takes a lot of time before I can be sure the saddle springs won't crunch through the supporting bracket when you are riding the bike. Lovely looking saddles but the old rice farmer story again.
Attachments
Last edited by a moderator: