I had to gently pry on the plates here to stretch the rubber gaskets enough to allow the plates to not overlap.

I had to gently pry on the plates here to stretch the rubber gaskets enough to allow the plates to not overlap.

  • 0
  • 0
I started with each Center Bolt on each Plate, then the 1st Bolt in each Plate, then the 3rd Bolt in each Plate, working my way around, gradually tigh

I started with each Center Bolt on each Plate, then the 1st Bolt in each Plate, then the 3rd Bolt in each Plate, working my way around, gradually tigh

  • 0
  • 1
Completed installation of new Sprocket onto Rear Wheel.

Completed installation of new Sprocket onto Rear Wheel.

  • 0
  • 0
Next is to mount the Rear Wheel back on the Bicycle.

Next is to mount the Rear Wheel back on the Bicycle.

  • 0
  • 0
Rear Wheel mounted. Put the Rear Fender back on.

Rear Wheel mounted. Put the Rear Fender back on.

  • 0
  • 0
Slide Push Rod into Rear Axle and tighten Shimano Bell Shifter onto Axle. Put Bicycle in 2nd Gear and adjust nut on cable to put yellow dot centered

Slide Push Rod into Rear Axle and tighten Shimano Bell Shifter onto Axle. Put Bicycle in 2nd Gear and adjust nut on cable to put yellow dot centered

  • 0
  • 0
Instead of drilling more holes in the frame of the Cargo-T, I went with making an adapter plate to mount the Front and using the supplied plate to mou

Instead of drilling more holes in the frame of the Cargo-T, I went with making an adapter plate to mount the Front and using the supplied plate to mou

  • 0
  • 1
Rear Motor Mount using supplied adapter plate, u-bolt and spacer in kit.

Rear Motor Mount using supplied adapter plate, u-bolt and spacer in kit.

  • 0
  • 0
I was able to use the supplied adapter plate and u-bolt that came with the kit for the Rear Motor Mount. I wrapped around the bicycle frame with elec

I was able to use the supplied adapter plate and u-bolt that came with the kit for the Rear Motor Mount. I wrapped around the bicycle frame with elec

  • 0
  • 0
I made a similar adapter plate from 1/4" Steel Bar and a 2" U-bolt for the Front Motor Mount

I made a similar adapter plate from 1/4" Steel Bar and a 2" U-bolt for the Front Motor Mount

  • 0
  • 0
DSC08670

DSC08670

  • 0
  • 0
DSC08671

DSC08671

  • 0
  • 0
Be sure to line up slot in Shuttle with tit inside Carburetor.

Be sure to line up slot in Shuttle with tit inside Carburetor.

  • 0
  • 0
Carb mounted to Air Intake.

Carb mounted to Air Intake.

  • 0
  • 0
Throttle Cable assembled and in Carburetor.

Throttle Cable assembled and in Carburetor.

  • 0
  • 0
Now to mount the throttle.

Now to mount the throttle.

  • 0
  • 0
Another view of the drilled hole.

Another view of the drilled hole.

  • 0
  • 2
Drilled a hole in the Right Handlebar to accept the pin on the Throttle.

Drilled a hole in the Right Handlebar to accept the pin on the Throttle.

  • 0
  • 0
DSC08681

DSC08681

  • 0
  • 0
DSC08682

DSC08682

  • 0
  • 0
DSC08683

DSC08683

  • 0
  • 0
DSC08684

DSC08684

  • 0
  • 0
DSC08685

DSC08685

  • 0
  • 2
DSC08686

DSC08686

  • 0
  • 0
D

Torker Cargo -T Flying Horse 2-Cycle Installation

Images showing the installation of a Flying Horse 2-Cycle Engine on a Torker Cargo-T with Shimano 3-Speed Hub. The initial installation took around 14 hours over 2 1/2 days. It ran beautiful for 2 days and then Magneto Loop Coil ceased to function.
Click to expand...
There are no comments to display.

Album information

Album owner
dinoseer
Date created
Item count
48
View count
2,221
Comment count
0
Rating
0.00 star(s) 0 ratings

Album privacy

D

dinoseer

Media items
57
Albums
0
Can view media items
Everyone
Can add media items
Album owner only

Share this album

Top