Could someone just tell me what I need?

[Wtg78]

What I find unusual bout that manifold is the pipe joints are laser welded, but not the flange.

I tried to get one of these and it was tiny do I have to and I asked for one that was 19 mm and they sent me something that looked as though it fit a model car. Idk. But that's what I want i am just skeptical about it because if that situation. I was trying to find one of the silicon angled tube's but haven't the idea on what size

 

[Wtg78]

Yeah I find a 19mm dellorto phbg is about perfect.

Thats what i have on it. So i guess I'll just keep what I got. So I can't use this at all?

 

[Wtg78]

Yeah I find a 19mm dellorto phbg is about perfect.

You're probably right but I was trying to get a different kind of carb there wasn't a dellorto because I've been through so many of them I've been through three of them in a year I'm just not cute up on carbs to be honest I don't know how to jet them or anything. So here's another learning lesson for me i guess. Thanx guys.ill let you know how it goes with everything

 

[Wtg78]

Where the carb mounts in the rubber boot, measure the spigot of the carburetor. Outside Diameter in mm

And thats how I get what size i should be getting cause I was going to get a angled rubber boot to get it to go out side the frame. And the only reason I'm trying to make this work is cause my 84 yr old mother thought she'd order me one and I want her to see it on there i honestly didn't have the heart to tell her it wouldn't work i just said "wow ty ma..I love you" and left her with that feeling instead..you know what I mean?

 

[Chainlube]

Perhaps they cut the offset off of something else then welded it to the flange.

The flanges are welded on in house and the tube is done somewhere else.

 

[robe]

You can make one with 3/4 street elbows. The trick is to find the right size of pipe to fit it together. Mine were made from an old towel bar and some really thin walled PVC pipe. I also put a couple o rings on the manifold and a set screw.
I used 1 inch heat shrink tubing to seal it up.

 

[Wtg78]

You can make one with 3/4 street elbows. The trick is to find the right size of pipe to fit it together. Mine were made from an old towel bar and some really thin walled PVC pipe. I also put a couple o rings on the manifold and a set screw.
I used 1 inch heat shrink tubing to seal it up.

Nice..and i could if I wanted to actually go out and find all that. I don't just have that lying around.but it is very crafty to say the least. I like it.but I am trying to buy one and i thought maybe I found it bit the inner dimensions are too big i think. It says it's 30mm but I have a

 

[Wtg78]

Nice..and i could if I wanted to actually go out and find all that. I don't just have that lying around.but it is very crafty to say the least. I like it.but I am trying to buy one and i thought maybe I found it bit the inner dimensions are too big i think. It says it's 30mm but I have a

And yes the bigger gas tank is a lot better looking i think it's 2.4 liters or so don't quote me on that but that's what I think. Not sure the gas mileage that I get but it's good I use a tank probably about once a week when I'm riding it steady more about every third use actually and the gas is not gone I just top it off.

 

[Daytripper24699]

I I need an offset manifold for a 21 mm pwk carburetor I'm thinking the little angled rubber piece and something else but I don't know what can somebody direct me in the right direction on exactly what you get so that I don't buy the wrong thing.

I believe it's a 32mm angled spigot intake, but don't just take it from me I could definitely be wrong...lol

 

[Daytripper24699]

I I need an offset manifold for a 21 mm pwk carburetor I'm thinking the little angled rubber piece and something else but I don't know what can somebody direct me in the right direction on exactly what you get so that I don't buy the wrong thing.

Like this but mines on a g2 reed set up and a Minarelli