scubaru89
Member
Can anyone recommend a bike or line of bike available anywhere from Amazon.com to a bike shop, something under $200 preferably under $150, mountain bike / hybrid and possibly front shocks??
scrubaru89
I have had very good luck and very bad luck with cheap, Chinese built bikes. I tend to find bikes built by Pacific bikes to be of fair quality as far as materials and welds go. I believe they market the cheaper, license built, Schwinns sold in big box stores, Kent/Next bikes, Genesis, and perhaps other brands. Assembly quality varies widely from bike to bike, likely due to differences in training, skill, and experience of the people doing the assembly of each component. My advice; take the bike completely apart, and reassemble it after cleaning each bearing and bearing race completely and using a good quality grease made for bicycles, available from a good local bike shop. When you disasemble each component, you will find some little more than finger tight and others so over tight as to warp the bearing races. Everything should be tightened till the bearing is starting to be difficult to turn/over tight, then loosened just slightly till it turns with some slight resistance. New bearings will soon loosen as they seat-in somewhat and you will have to re-tighten everything after a few months, so very slightly overtighten them a little at first. Unless you are going with front wheel drive, the cheap original front wheel will probably last for years if not abused. The driven wheel, usually the rear wheel, should be chucked out in faver of a very good quality wheel with at least 12 gauge spokes, in my opinion. Replace tubes with good quality ones. I also put thornpruff liners, high quality spoke hole cover cloth tape, and a quality factory slimed tube in the driven wheel, as repairing a flat in the drive tire is a b***ch in most MBs. If you are using a Happy Time/China Girl kit, seriously consider replacing the poorly engineered "rag joint" with a quality sprocket flange hub machined from a solid alloy billet and lacing it to a good quality double wall alloy rim with good SS spokes right from the get-go to save yourself grief in the future. Replace the original equipment garbage brake pads with Koolstop, Rav-X or other good quality brake pads. Ask your local bike shop what they reccomend as the best. Saving a few bucks on brakes is just plain stupid.
Great luck on your MB build. Best advice is take your time and do it right the first go-around and you will have a good time riding you MB instead of the endless tinkering some of us do.
Mike
I have motorized a bike with discs front and rear, several with a disc on the front, and several with rim brakes. I replaced the brake arms with longer ones on one bike because I wanted to clear a set of polycarbonate fenders and I felt more leverage would be an improvement, and on that bike it did help to shorten the stopping distance considerably. I have 2 MBs right now, 1 with a front disc and one with 2 rim brakes. A front disc is an improvement, but cheap Chinese bikes come with cheap disc brakes, so I replaced mine with a BB-5 caliper and I automatically replace rim brake pads with better quality ones. I feel a good set of rim brakes are up to the job 98% of the time. If you go over 30MPH often, or ride down steep, long hills a lot of the time, then upgrading to a front disc is a great idea. I do most of my riding on bike, hike, and roller blade paths used by young people with ear buds in and music blasting, as well as older folk who move slowly and may not hear so well. To be polite and a good human being, I generally hold it down to 20MPH or less so I don't hurt others. Rim brakes are more than adequate at such speeds. A biker I know made a cross country tour and melted/blew out his tires overusing his brakes on a long down-mountain ride. The crash was bad and every bike he's had since has disc brakes, front and rear. How and where you ride is key to the decision as to what brakes you need. Good brakes, rim or disc, are generally good enough for most of us most of the time. Keep them clean and in good adjustment. I think you have a good head on your shoulders and I'm sure you will think everything through and not just throw a bike together, willy nilly, then go out and blast down a crowded street at 35-40 MPH, hoping luck will keep you and your neighbors in one piece.
Enjoy the whole experience, planning the bike, amassing the parts, building a good solid safe MB, and then having fun riding that bad boy in a reasonable manner for many years, as I'm sure you will.
In a way I do want to find a used bike that is of better quality, but I am afraid either I'm taking the risk with a craigslist find or I'm still paying over $200 at a bike shop for a reconditioned bike. I just don't have the money.
I always upgrade my rear rim atleast to a 13gauge spoke rim. Wouldn't wanna fold a tire doing 35. They just arent built to hold the constant high speed. Make sure you keep you bearings greased!So I finally bought an engine from bikeberry.com and it should be here in a few days. I had been looking however for a usable bike without much luck in the lower price range. I have been up and down craigslist and ebay and the only bike I found usable turned out to be a total nightmare of rust and bad parts.
So I have picked up a Roadmaster Granite Peak 26" bike from Wally World.
http://www.walmart.com/ip/Roadmaste...gMethod=Recommendation:wm:RecentlyViewedItems
I've seen an engine fit on this bike on two different youtube videos and mentioned on one or two forums. However my issue is the reliability. I understand this is a Walmart bike so its obviously built with very cheap components, some of which are the bearings for the rear wheel.
My logic is I will be using it to travel to and from school which is 2 miles each way, and to work which is 4 miles each way. I am in the city of Williamsport so speeds are 25 mph and there are plenty of stop lights to keep me doing maybe 15 tops. I feel if the bearings do wear out it shouldn't be that hard to replace them or even replace the whole back wheel.
I figured why pay a higher price for something that I am going to be taking apart to upgrade parts on, and its a cheap commuter. So should I be worried about trouble from a cheaper bike?