I got external spock but no ignition.

Discussion in 'Electrical' started by inspectorcritic, Dec 1, 2016.

  1. Like the idea long as I don't loose my finger should I expect that it blast my finger off or how many pounds might find a mechanic?
     

  2. johnsteve

    johnsteve Member

    give me ignition, warp factor drive scotty. Is that affirmative Mr Spock, and becareful with that lasar McCoy, its highly deadly
     
  3. CrazyDan

    CrazyDan Active Member

    Just use your stubbiest finger that still fits, not your pinky :p. It shouldn't blow your finger across the room just push air around it lol. It's not a way to see how much compression you have unless you are a genius with sensitive fingers, just shows whether there is compression or not.
     
  4. crassius

    crassius Well-Known Member

    many auto parts stores will loan you a compression gauge free
     
  5. Got spock-got gas-got crack! Don't believe it such a small defect shut down everything must be a very sensitive port for a ported GT 80 66cc and I know Gasbike.com doesn't want to warrantee its going be another long agnozing argument with that comppany I hate. Still early how much to replace compare to just buying another motor just be done with the heart ache.
    By the way your comments are the most informative thanks you draw a clear picture in the chaos.
     

    Attached Files:

  6. I got a defective cylinder ported GT 80 66cc can I just buy a standard 66cc and slide it in without problems and vice versa?
     
  7. .... and there is no such thing of 80 cc engine ETHER!
     

    Attached Files:

  8. Street Ryderz

    Street Ryderz Active Member

     
  9. crassius

    crassius Well-Known Member

    how is it defective? pic would help

    there are many different port mappings and cylinder heights out there these days - mix & match is a real problem
     
  10. Nate888

    Nate888 Member

    bad rings can cause loss of compression. so can loose header bolts, blown head gasket, bad or loose sparkplug, etc.
     
  11. Nate888

    Nate888 Member

    also it should take a lot more effort to turn with the plug in place. if it makes a hissing or sucking noise and turns over too easily with the clutch engaged, that's a sure sign of compression failure
     
  12.  

    Attached Files:

  13. crassius

    crassius Well-Known Member

    hard to tell from pic, but it might be cleaned up & used OK
     
  14. Kolobo

    Kolobo Guest

    Be real tiff to get to that port looks like the Chinese red devil press his thumb on it made a broken indentation, trying start sounds like a sick AIR breather.
    Got real good deal for 66 cylinder includes piston rings gaskets everything 12 bucks but the goddamn site is refusing my visa. Hope I send it direct.
     
  15. Randall

    Randall Member


    LOL :D
     
  16. CrazyDan

    CrazyDan Active Member

    I've laughed my ass off watching them schizos freak out because of motion blur..."Did you see that!!! OMFG DID YOU SEE THAT!!!" seems they all believe in niburu as well, and most look like they are regular meth users.
     
  17. Finally maybe some reliefe in this case Gasbike sent me an email said they would send me a new ported cylinder, never thought they would honor there warrantee hope it gets drop in the mail by tomorrow before they change their minds.
     
    Street Ryderz likes this.
  18. Nate888

    Nate888 Member

    yeah, but it's gasbike.net, so at least for yourself you should know you gotta assume they'll most likely need an extra three days to 'be themselves' or whatever they do, before actually doing anything
     
  19. Nate888

    Nate888 Member

    but I ordered all my stuff from gas bike. net and overall I got good value stuff, thoughtfully paired combos, and lackadaisical service. so I gotta say it wasn't bad, despite the extra week it took and the mystery of the two bottom bracket bearings: there was a US '70s style adapter cone set that included open cage ball bearings and everything to actually work with the very oversized bottom bracket housing on the 'skyhawk style' gt2 Alum. bike frame I got in my order. but intriguingly there was also a sealed BB, which is supposed to be all around higher performance. however, there was no way to use it - the local bike shop even couldn't see how you could use it with the frame - so I gave it to a friend who was helping me with the build
     
  20. IMG_20161210_131130.jpg IMG_20161210_131816.jpg More rotten crap the China man at the shanghai motorfactory put the piston in backward causing motor death agony saddness and in general just piss off note the scoreing cylinder side. I could buy a brake honer and hone it for $17.00 but don't want to piss with this one lasted almost 7 hrs. sorry for picture screwups missloads this is not the port one I have nothing but problems I pay for from Asia so far my average is 16 junk products out 16 products that I purchas have been junk shanghai sh*t that a big 100% junk record.
     

    Attached Files:

Loading...