What would we call this?

[Street Ryderz]

Had some time this evening so I made up my new flange and header it's looking good!This one is as big as I can see fitting on the stock stud spacing It's 27mm across and 22mm in height with an id of 27mm or 1 and 1/8 " an 1/8th larger than anything commercaily available and just fits nicely!The port in the last pic isn't opened as much as my current ones so you can see that it will fit the larger port area no problems!

 

[gary55]

Had some time this evening so I made up my new flange and header it's looking good!This one is as big as I can see fitting on the stock stud spacing It's 27mm across and 22mm in height with an id of 27mm or 1 and 1/8 " an 1/8th larger than anything commercaily available and just fits nicely!The port in the last pic isn't opened as much as my current ones so you can see that it will fit the larger port area no problems!

Time for a bigger carb I'd say. That thing is gona suck the bowl dry.

 

[Street Ryderz]

Time for a bigger carb I'd say. That thing is gona suck the bowl dry.

LOL quite possibly,Ive been looking to get the vm 18 but havent yet!I might have to go with a 20mm carb not sure but it's looking like it!The larger port volumes are making it hard to get set up with a 19mm header holding it back the heat builds fast and messes with my jetting!

 

[Street Ryderz]

LOL quite possibly,Ive been looking to get the vm 18 but havent yet!I might have to go with a 20mm carb not sure but it's looking like it!The larger port volumes are making it hard to get set up with a 19mm header holding it back the heat builds fast and messes with my jetting!

s**t I just did the equivalent dia for the rectangle port shape and it's 27.32 just slightly larger still than the header dia I hope it works because there is no way to fit any larger LOL!

 

[gary55]

LOL quite possibly,Ive been looking to get the vm 18 but havent yet!I might have to go with a 20mm carb not sure but it's looking like it!The larger port volumes are making it hard to get set up with a 19mm header holding it back the heat builds fast and messes with my jetting!

Like the sound of the 20. Have you thought about some ground affects? Maybe some winglets to counter high speed wobble. Bet this one is gona fly.

 

[Street Ryderz]

Had some time today between two customer builds and started making up the tubes and trail fitting the stepped conections for this pipe!I think it's going to work out well!

 

[Street Ryderz]

So here it is fitted up and welded I need to dress the welds yet and come up with the rear hanger but I like it looks serious!Going to see if high heat caliper paint will hold up for it I've used it on pipes with ok results before!

 

[Street Ryderz]

That never ending quest for more!I spoke before about how I took the CNS carb that stock was 16mm and bored it out to 17.5mm then later said that it might be posible to go to 18mm and then that would be it maxed out,Well I went ahead and opened it to 18mm and it worked but thats all in as big as it can get and dam it I still need more!LOL going to have to try a vm 20!

 

[Frankenstein]

That never ending quest for more!I spoke before about how I took the CNS carb that stock was 16mm and bored it out to 17.5mm then later said that it might be posible to go to 18mm and then that would be it maxed out,Well I went ahead and opened it to 18mm and it worked but thats all in as big as it can get and dam it I still need more!LOL going to have to try a vm 20!

Ya zaht is von deep throat. Wunderbar!

 

[Street Ryderz]

Time for a bigger carb I'd say. That thing is gona suck the bowl dry.

You were absolutely right brother it sucks the bowl dry in no time faster than it's able to replentish it's self! and the bowl size for the vm20 is pretty much the same as what I have now SIGH!!