Avenger 85 question

sherron82

Active Member
Local time
1:46 AM
Joined
Nov 9, 2023
Messages
286
Location
Morristown TN
What up everyone, hope you all had a great Christmas, I know I did.... I have a question, if I was to do some light port work to my avenger, what should I do? Should I lower the exhaust a little, I see that when the piston is all the way down you can not see the top of piston thru the exhaust port and the same with the intake side when the piston is all the way up. So does that mean I shouldn't do any port work? Little new to this so please bear with me.. the squish gap is . 8 so that seems good... Thanks for all your help
 
Here is some pictures with piston all the way down and up. And should I use the 16mm carb that came with the wildcat 80, up carb or just use the one that came with it
 

Attachments

  • IMG_20231226_094928282.jpg
    IMG_20231226_094928282.jpg
    95.9 KB · Views: 150
  • IMG_20231226_094940852_HDR.jpg
    IMG_20231226_094940852_HDR.jpg
    89.4 KB · Views: 106
  • IMG_20231226_095006757.jpg
    IMG_20231226_095006757.jpg
    147.8 KB · Views: 97
  • IMG_20231226_095106090.jpg
    IMG_20231226_095106090.jpg
    146.4 KB · Views: 106
  • IMG_20231226_095200083_HDR.jpg
    IMG_20231226_095200083_HDR.jpg
    123.1 KB · Views: 123
Finally got around to checking my cylinder to find out why mine died. Looks like I had a few pieces of casting come loose. Better clean it up as much as possible!
 

Attachments

  • 20231226_084431[1].jpg
    20231226_084431[1].jpg
    111.3 KB · Views: 133
  • 20231226_084450[1].jpg
    20231226_084450[1].jpg
    140 KB · Views: 129
Ok thanks and I plan on doing that. Looks pretty clean but I'm still gonna do it. How did yours run? All stock?
 
All stock, pulled great, never went over 9k rpm because of break-in. Have a new cylinder on order.
 
Here is some pictures with piston all the way down and up. And should I use the 16mm carb that came with the wildcat 80, up carb or just use the one that came with it
All you should do right now is round off the inner edge of the ports, you can use sandpaper for that. Then rinse it out with a some clean mixed fuel. The exhaust side looks perfect, so need to change anything there.

I'm curious what the business side of the head looks like? Do you have a picture of that?
 
I plan on getting the one from gomax soon but here is the stock one
 

Attachments

  • IMG_20231226_112713826.jpg
    IMG_20231226_112713826.jpg
    159.5 KB · Views: 103
  • IMG_20231226_112707923.jpg
    IMG_20231226_112707923.jpg
    158.5 KB · Views: 105
  • IMG_20231226_112652291.jpg
    IMG_20231226_112652291.jpg
    209.6 KB · Views: 99
Does this look good?
 

Attachments

  • IMG_20231226_114817761.jpg
    IMG_20231226_114817761.jpg
    79.7 KB · Views: 90
  • IMG_20231226_114826925.jpg
    IMG_20231226_114826925.jpg
    108.5 KB · Views: 85
  • IMG_20231226_114826683.jpg
    IMG_20231226_114826683.jpg
    103.5 KB · Views: 78
  • IMG_20231226_114851445.jpg
    IMG_20231226_114851445.jpg
    88 KB · Views: 100
Back
Top